NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
50 reportsMileage unknown · Aug 10, 2021
Engine
I received error code P052B and the car had a high pitched whistle and was way down on power. I had it towed to the nearest dealer for service. After speaking with the technician, they told me they'd gone through with a boroscope and saw nothing out of the ordinary and recommended a new valve cover since the PCV was bad. I opte…
Read full complaint
I received error code P052B and the car had a high pitched whistle and was way down on power. I had it towed to the nearest dealer for service. After speaking with the technician, they told me they'd gone through with a boroscope and saw nothing out of the ordinary and recommended a new valve cover since the PCV was bad. I opted to order replacement spark plugs, coils, an eccentric valve sensor, and figured why not replace the Vanos bolts while in there too. Unfortunately after getting the cover off, it's been discovered that 7! of the Vanos bolts have already either sheared off or backed out. Pretty much a worst case scenario as my car was built in 2010 and is just outside the 10 year unlimited mile warranty outlined in the service bulletin (https://static.nhtsa.gov/odi/rcl/201...4V176-2716.pdf). This service warranty does not appear long enough, and the item should have been recalled instead of warrantied. (Similar years similar issue in the BMW N55 motor was recalled https://www.autoblog.com/2014/04/11/bmw-broadens-engine-bolt-recall-nearly-half-million-cars-worldwide/)
NHTSA ODI #11428492
42,000 miles · Jun 25, 2021
Air Bags
The contact owns a 2011 BMW 128I. The contact stated while entering the vehicle she noticed that the passenger’s seat occupancy sensor light was illuminated however, there was no one occupying the seat. The contact stated that the warning light remained illuminated. The contact took the vehicle to the local dealer who inspected …
Read full complaint
The contact owns a 2011 BMW 128I. The contact stated while entering the vehicle she noticed that the passenger’s seat occupancy sensor light was illuminated however, there was no one occupying the seat. The contact stated that the warning light remained illuminated. The contact took the vehicle to the local dealer who inspected the vehicle and diagnosed the failure as a faulty memory SRS light and sensor. The contact was informed that to repair the failure the passenger’s seat needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 42,000.
NHTSA ODI #11422305
Mileage unknown · Nov 6, 2020
Engine
CAMSHAFT HOUSING BELTS ARE LOSSES OR BROKEN
NHTSA ODI #11373441
81,000 miles · Oct 15, 2020
EnginePower TrainVehicle Speed Control
VANOS FAILED ON 2011 BMW 128I, MANUFACTURE OFFERED EXTENDED WARRANTY AND FAILED TO HONOR SAID WARRANTY. VEHICKLE MAKES LOUD NOISE. CAR WILL EVENTUALLY BREAK MAKING CAR UNDRIVABLE EVER AGAIN, WITH 7K REPAIR COST WHICH EXCEEDS VALUE OF CAR WITH LESS THAN 100K MILES
NHTSA ODI #11364505
74,000 miles · Mar 24, 2020
Electrical SystemElectronic Stability Control (esc)Unknown Or Other
WATER ACCUMULATES IN THE TRUNK/BOOT OF THE VEHICLE CAUSING NUMEROUS ELECTRONIC FAULTS, ERROR CODES AND STATES PER BMW THIS ISSUE SIGNIFICANT. MANY ISSUES LIKE THE ONES I'VE DESCRIBED WERE RECALLED TO A DEGREE. NOW, THEIR 'FIXES' ARE FAILING AND MORE AND MORE ISSUE EMERGE WITH THE BMW E8X FRAME. I WAS TOLD PER BMW THAT THESE RECA…
Read full complaint
WATER ACCUMULATES IN THE TRUNK/BOOT OF THE VEHICLE CAUSING NUMEROUS ELECTRONIC FAULTS, ERROR CODES AND STATES PER BMW THIS ISSUE SIGNIFICANT. MANY ISSUES LIKE THE ONES I'VE DESCRIBED WERE RECALLED TO A DEGREE. NOW, THEIR 'FIXES' ARE FAILING AND MORE AND MORE ISSUE EMERGE WITH THE BMW E8X FRAME. I WAS TOLD PER BMW THAT THESE RECALLS REMEDY THE MISTAKE; THEREFORE, EVEN THOUGH I HAVE THE SAME ISSUES THE RECALL COVERED I'M HAVING THE SAME ISSUES. THESE ISSUES CAN HAPPEN AT ANY TIME. MOST OFTEN WHEN STARTING THE VEHICLE BUT ON PARTICULARLY RAINY DAYS IT CAN BE ANY TIME AND ANYWHERE.
NHTSA ODI #11319195
53,857 miles · Mar 25, 2019
Electrical System
CONVERTABLE TOP NOT OPERATING.
NHTSA ODI #11191402
43,000 miles · Apr 26, 2018
Service Brakes
ON THE CONVERTIBLE MODEL THERE IS A REAR BRAKE LIGHT BAR LOCATED ON THE TRUNK DECK. THIS LIGHT BAR HAS FALLEN OFF MY VEHICLE 4 TIMES IN 43000 MILES. IT IS NOT A VERY EFFECTIVE BRAKE LIGHT IF IT KEEPS FALLING OFF. THIS IS OBVIOUSLY A DEFECT IN WHAT IS SUPPOSED TO BE A SAFETY FEATURE.
NHTSA ODI #11090321
118,000 miles · Feb 7, 2018
EngineFire
TL* THE CONTACT OWNS A 2011 BMW 128I. THE CONTACT STATED THAT THE BATTERY WARNING INDICATOR FLASHED MORE THAN ONCE AND, WHILE DRIVING IN REVERSE, SMOKE EMITTED FROM THE VEHICLE UNDER THE HOOD. THE VEHICLE WAS PULLED BACK INTO THE GARAGE DUE TO THE FAILURE. THE DEALER (FIELDS BMW WINTER PARK, 963 WYMORE RD, WINTER PARK, FL 32789,…
Read full complaint
TL* THE CONTACT OWNS A 2011 BMW 128I. THE CONTACT STATED THAT THE BATTERY WARNING INDICATOR FLASHED MORE THAN ONCE AND, WHILE DRIVING IN REVERSE, SMOKE EMITTED FROM THE VEHICLE UNDER THE HOOD. THE VEHICLE WAS PULLED BACK INTO THE GARAGE DUE TO THE FAILURE. THE DEALER (FIELDS BMW WINTER PARK, 963 WYMORE RD, WINTER PARK, FL 32789, (407) 628-2100) WAS UNABLE TO VERIFY WHEN THE MANUFACTURER WOULD SUPPLY THE REMEDY AND PARTS FOR NHTSA CAMPAIGN NUMBER: 17V683000 (ENGINE AND ENGINE COOLING). THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 118,000. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
NHTSA ODI #11071529
87,000 miles · Jan 24, 2018
Unknown Or Other
REFERENCE PCV VALVE HEATER RECALL. MY CAR STARTED SMOKING BETWEEN A MONTH AND A HALF TO TWO MONTHS AGO. I HAVE TALKED TO BOTH REGIONAL AND LOCAL BMW. THEY SAID THERE WERE GOING TO MAKE ARRANGEMENTS FOR ALTERNATIVE TRANSPORTATION BUT I HAVEN'T HEARD FROM THEM SINCE 1/16/18. MY CAR IS NOTICEABLY SMOKING WHILE STATIONARY, AND YOU C…
Read full complaint
REFERENCE PCV VALVE HEATER RECALL. MY CAR STARTED SMOKING BETWEEN A MONTH AND A HALF TO TWO MONTHS AGO. I HAVE TALKED TO BOTH REGIONAL AND LOCAL BMW. THEY SAID THERE WERE GOING TO MAKE ARRANGEMENTS FOR ALTERNATIVE TRANSPORTATION BUT I HAVEN'T HEARD FROM THEM SINCE 1/16/18. MY CAR IS NOTICEABLY SMOKING WHILE STATIONARY, AND YOU CAN SMELL PLASTIC BURN SMELL WHEN DRIVING. AT FIRST, I CONTACTED REGIONAL BMW SOMETIME DURING EARLY DECEMBER. THEY ADVISED ME TO CONTACT MY LOCAL BMW IN REFERENCE TO GETTING ME INTO ALTERNATIVE TRANSPORTATION UNTIL MY RECALL PARTS WERE AVAILABLE. BMW OF OCALA TOLD ME THEY HADN'T HEARD ANYTHING ABOUT ALTERNATIVE TRANSPORTATION AND THAT MY CAR WOULD NOT BE SMOKING DUE TO THE RECALL. I PARKED MY CAR AND UNDID THE BATTERY ON 12/30/17. I TRIED TO START MY CAR ON EITHER 1/14/18 OR 1/15/18 AND IT STARTED SMOKING AGAIN IMMEDIATELY. I CONTACTED REGIONAL ON 1/16/18. THEY TOOK MY INFORMATION (MILEAGE, PURCHASE DATE, PLACE PURCHASED, AND PLACE CALLED FOR ASSISTANCE), AND GAVE IT TO A CASE MANAGER AT REGIONAL. THE REGIONAL MANAGER TYLER CONTACTED ME BACK THE SAME DAY 1/16/18 AND TOLD ME HE FAXED MY INFORMATION AND INSTRUCTIONS OVER TO BMW OF OCALA AND I SHOULD HEAR FROM THEM IN 1-2 DAYS AND IF NOT, TO CALL HIM BACK. I'VE BEEN CALLING TYLER AND LEAVING MESSAGES SINCE 1/19/18 AND HAVE NOT HEARD BACK FROM HIM, OR BMW OF OCALA. MY CAR IS NOT SAFE AND I CAN NOT DRIVE IT. THE NUMBER I HAVE BEEN CALLING FOR REGIONAL BMW IS 1800-831-1117. TYLERS EXTENSION THERE IS 7389.
NHTSA ODI #11064648
Mileage unknown · Jan 4, 2018
Electrical SystemExterior Lighting
MY CAR HEADLIGHTS AND ALL INSIDE PANEL LIGHTS WENT OUT ON THE CAR. I NEED HELP BECAUSE NO ONE SEEMS TO CAN TELL ME WHAT IS WRONG AND HOW TO GET IT FIXED. I DO KNOW THAT A RECALL ON ELECTRIC SYSTEMS HAPPENED IN OCTOBER BUT MY CAR WAS NEVER FIXED. I LIVE IN LAUREL MS. MY TWO FRONT WINDOWS STOPPED WORKING THE SAME TIME THAT ALL LIG…
Read full complaint
MY CAR HEADLIGHTS AND ALL INSIDE PANEL LIGHTS WENT OUT ON THE CAR. I NEED HELP BECAUSE NO ONE SEEMS TO CAN TELL ME WHAT IS WRONG AND HOW TO GET IT FIXED. I DO KNOW THAT A RECALL ON ELECTRIC SYSTEMS HAPPENED IN OCTOBER BUT MY CAR WAS NEVER FIXED. I LIVE IN LAUREL MS. MY TWO FRONT WINDOWS STOPPED WORKING THE SAME TIME THAT ALL LIGHTS WENT OUT.
NHTSA ODI #11058578
Official recalls
7Mar 2, 2022
BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3 Series Convertible (328i); 2006-2010 5 Series Sedan (525i, 525xi, 528i, 528xi, 530i, 530xi); 2006-2007 5 Series Wagon (530xi); 2007-2010 X5 SAV (X5 3.0si, X5 xDrive30i); 2006-2008 Z4 Coupe (Z4 3.0si); and 2006-2011 Z4 Roadster (Z4 3.0i, Z4 3.0si, Z4 sDrive30i) vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
Consequence & remedy
Consequence: An electrical short can cause the PCV valve heater to overheat, increasing the risk of a fire while driving or, soon after driving when parked.
Remedy: This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.
Jan 15, 2020
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
Aug 6, 2019
BMW of North America, LLC (BMW) is recalling certain 2008-2012 BMW 128i, 135i, 135is Coupes and 128i, 135i Convertible vehicles. The wiring and electrical connectors in the blower-regulator wiring harness may overheat.
Consequence & remedy
Consequence: Wiring that overheats could cause the electrical connectors to melt, and increase the risk of a fire, even when the vehicle is unattended.
Remedy: BMW will notify owners, and dealers will inspect the blower-regulator wiring harness, and replace it with a new part, free of charge. The recall began October 4, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of an earlier recall number 17V-676.
Oct 30, 2017
BMW of North America, LLC (BMW) is recalling certain 2008-2011 128i and 2007-2011 328i, 328xi, 328i xDrive, 525i, 525xi, 528i, 528xi, 530i, 530xi, X3 3.0si, X3 xDrive30i, X5 xDrive30i, Z4 3.0i, Z4 3.0si and Z4 sDrive30i vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
Consequence & remedy
Consequence: An electrical short can cause the parts within the PCV valve to melt, increasing the risk of a fire, even when the vehicle is not in use.
Remedy: BMW will notify owners, and dealers will replace the PCV valve heater, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notification by the end of October 2018. Owners may contact BMW customer service at 1-800-525-7417.
Feb 5, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2008-2013 128i and 135i coupes and convertibles and 1 Series M coupes, 2006-2011 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 335i, 335xi, 335i xDrive Sedans, 2009-2011 335d sedans, 2006-2012 325xiT, 328i and 328xi sports wagons, 2007-2013 328i, 328xi, 328i xDrive, 335i, 335xi, 335i xDrive, 335is and M3 Coupes and Convertibles, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i SAVs, 2007-2010 X3 xDrive30i SAVs, 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M SAVs, 2009-2013 BMW X5 xDrive35d SAVs, 2008-2014 X6 xDrive35i, X6 xDrive50i, and X6 M SACs, 2010-2011 BMW X6 xDrive50i SACs and 2008-2011 M3 Sedan vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's frontal air bag module or inflator depending on the vehicle model, free of charge. The recall began March 9, 2018. Owners may contact BMW customer service at 1-800-525-7417.
Apr 10, 2014
BMW of North America, LLC (BMW) is recalling certain model year 2010-2011 128i Coupe, 128i Convertible, 328i Sedan, 328i xDrive Sedan, 328i Coupe, 328i Convertible, 328i Sports Wagon and Z4 sDrive 30i, 2011-2012 135i Coupe, 135i Convertible, 335i Sedan, X5 xDrive 35i, and X6 xDrive 35i, 2011 335i xDrive Sedan, 335i Coupe, 335i Convertible, 528i Sedan, 535i Sedan, 535i xDrive Sedan, X3 xDrive 28i, and X3 xDrive 35i, 2010 X3 xDrive 30i, and X5 xDrive 30i, 2012 640i Coupe, and 640i Convertible and 2010-2012 535i Gran Turismo vehicles. In the affected vehicles, the bolts that secure the housing for the variable camshaft timing adjustment (VANOS) unit can loosen over time and may possibly break.
Consequence & remedy
Consequence: If the bolts loosen or break the engine may have reduced power or stall. An engine stall increases the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the four VANOS housing bolts for both VANOS units (intake and exhaust), free of charge. In addition, owners of approximately 170,172 model year 2010-2012 BMW vehicles equipped with inline 6 cylinder engines not covered by this recall, will receive an extended warranty to address this condition. The recall began on September 24, 2014. Owners may contact BMW at 1-800-525-7417.
Feb 7, 2013
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence & remedy
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (3)
Electrical System:wiring:fuses And Circuit Breakers
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Electrical SYSTEM:12V/24V/48V Battery:cables
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Electrical System
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration