2018 Audi Q5

Incident Description: While accelerating from a red light during rush hour, the vehicle suffered a sudden, catastrophic loss of steering control. The steering wheel locked completely and could not be turned. Simultaneous loud, long beeping and dashboard warnings appeared, stating: "Steering malfunction stop the vehicle immediately." The vehicle was immobilized in the middle of a highly congested, complex 5x5 intersection. Local police had to shut down traffic until the vehicle could be cleared. Safety Risk: Stalling abruptly in a major intersection during rush hour created an immediate risk of a multi-car rear-end pile-up. This jeopardized the safety of the driver and multiple children who were inside the vehicle, who faced a severe personal injury risk whether they remained trapped in the active roadway or attempted to exit. Diagnosis, Cost, and Recall Context: The vehicle was towed to an authorized dealership. Diagnosis revealed significant water intrusion inside the steering wheel wiring harness. Draining the water cleared the error and the vehicle become operational, but the dealership quoted $6,000 in repairs to replace the steering components completely out-of-pocket cost. Please note it appears the $6,000 quote will be out-of-pocket for catastrophic safety defects although they may be known issues for the same make and model years: Prior Gateway Recall: This vehicle’s VIN was previously impacted by the Gateway module recall (where water intrusion triggers a limp mode). That recall was redeemed prior to this event, and my understanding the repair should have prevented moisture intrusion. There seems to be a history on this make and model for known moisture intrusion causes critical issues. U45 Warranty Exclusion: The manufacturer issued a warranty extension for this exact steering failure on this same make and model years. However, this specific VIN was excluded from coverage, despite it being within the parameters.

Description of Incident and Safety Defect:Failed Component & Inspection Availability: The gateway control module, located in an unsealed floor compartment under the rear seat, failed due to liquid/moisture intrusion. The damaged module and vehicle are fully available for inspection upon request.Safety Risk: The sudden short-circuit of this module forced the vehicle into an immediate emergency "limp mode" and partial drivetrain shutdown while actively driving on the road. Unexpectedly losing engine power and throttle responsiveness in active traffic put my safety and the safety of surrounding drivers at an immediate, severe risk of a collision.Dealer / Independent Confirmation: The failure has been officially confirmed by an authorized Audi dealership service center. However, the dealer refused to perform a free safety repair because Audi has excluded my specific VIN from the active recall list.Prior Inspections: Outside of the diagnosing Audi dealership service center, the vehicle and failed component have not yet been inspected by the manufacturer, police, or insurance representatives.Warning Lamps & Prior Symptoms: Immediately prior to the drivetrain failure, the dashboard lit up with sudden error messages and warning lamps regarding a critical system malfunction. There were no gradual symptoms or warning signs leading up to this incident; the catastrophic module failure occurred suddenly due to moisture contacting the unsealed component.Summary Assessment:This vehicle has suffered the identical engineering defect and hazardous failure mode detailed in NHTSA Recall Campaign 21V-947 (Audi Recall Code 90S9). Audi’s current recall window is too narrow. It must be expanded to include all 2018 Audi Q5 vehicles experiencing this exact, catastrophic safety failure, regardless of their production date cut-offs. To date the car has 89924 miles

XXX My wife drive her 2018 audi q5 2.0 on express way with mother([XXX]),the car suddenly stall and lost all power ,because car bcm2 module has suffered liquid damage due to known vehicle design defect, towing to nearest repair shop change new bcm2 module and fix wire spend near $4000.00 dollars . INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

My 2018 Audi Q5 experienced significant water intrusion due to a failure of the panoramic sunroof drain system. Water entered the vehicle interior and traveled down into the electrical compartment, submerging the comfort module and damaging multiple wiring harnesses. This caused the vehicle to become inoperable and unable to start. Audi has issued Technical Service Bulletin 2075969/2 describing this exact defect. The bulletin states that the sunroof drain hoses can be kinked during factory installation of the headliner, which blocks drainage and causes water to enter the vehicle. This is a manufacturing defect affecting multiple model years of the Audi Q5. In my case, the water intrusion caused electrical failure, loss of vehicle function, and required thousands of dollars in repairs. Audi declined to cover the defect and stated the vehicle was not maintained on schedule, even though maintenance has no relationship to kinked or improperly routed sunroof drains. This defect poses a safety risk because water intrusion into electrical components can cause sudden vehicle failure, electrical shorts, corrosion, and loss of critical systems. The failure occurred without warning. I am reporting this because the issue appears to be widespread, documented by Audi, and has the potential to disable vehicles unexpectedly.

I wrote Audi to request escalation of an unresolved issue involving my 2018 Audi Q5, related to Safety Recall 90S9 (NHTSA Campaign 21V947000) for the gateway control module. Summary of the issue: My vehicle recently experienced a complete gateway control module failure due to water intrusion. I lost steering and brake assist warnings while driving, and the vehicle would not restart after being pulled over safely. It was towed first to the nearest Audi mechanic who diagnosed the issue as Recall 90S9. We then contacted Audi Memphis for inspection by them since it was a recall issues and paid a 2nd towing charge. Audi Memphis (owned by Gossett Motor Cars) said they could not do anything until they looked at the car. I have since obtained a copy of the original repair order from when Recall 90S9 was performed on my vehicle. The vehicle at the time of recall repair was owned by my Mother. The recall requires two remedies: (1) installation of a protective cover over the gateway control module, and (2) sealing of an underbody seam on vehicles produced before September 2021. The repair order shows a technician comment reading "INSF" next to the seam sealant line item, which indicates the sealant application was noted as insufficient at the time of the original recall service. Despite this documentation, and despite towing my vehicle in specifically for a 2nd inspection, Audi Memphis has stated they have no findings and no liability for the current failure. Given that: • My vehicle is included in the affected range for Recall 90S9, • The original repair order appears to document an incomplete or insufficient sealant application, and • Audi's own 90S9 technical bulletin states that damages resulting from improper repair or failure to follow the work instructions are the dealer's responsibility, I am requesting that this case be escalated for review. The current gateway control module repair be repaired at no cost to me. I currently have no working vehicle.

The dashboard displayed a solid red brake light with a flashing warning “stop vehicle safely” light. A professional diagnostic scan confirmed a permanent hard fault on the ABS control Module (J104) and Hydraulic Unit (N55). The vehicle has only 66,755 miles. Independent repair shops cannot service this unit because it requires highly restricted, specialized Audi factory programming and coding software, forcing consumers to face massive dealership replacement costs for a premature electronic failure ona critical safety system.

The contact owns a 2018 Audi Q5. The contact stated while driving at an undisclosed speed, the engine seized. No warning lights were illuminated. The contact stated while attempting to start the vehicle, the vehicle failed to start. The contact replaced the battery. The contact stated while attempting to start the vehicle, the vehicle failed to start. The vehicle was towed to an independent mechanic, however the vehicle was not diagnosed. The independent mechanic attempted to start the vehicle, however the vehicle failed to start. The independent mechanic inspected the vehicle and noticed that the gateway control modular was moist. The contact was informed that the gateway control module had become moist because of the broken seal, the vehicle shut down. The contact stated that the contact's wife had spilled a liquid substance into the vehicle. In addition, the contact was provided pictures of the corrosion. The contact referenced an unknown recall which had a similar failure description, however the contact's VIN was not associated. The dealer was made aware of the failure. The contact was informed that the repair was not covered under the recall. In addition, the contact was informed that the unknown recall only covered the seal. The contact was informed that the recall did not cover the replacement of the gateway control modular. The manufacturer was made aware of the failure and a case was filed. The contact was informed that the repair of the corroded seal was covered under the recall. The contact was advised to take the vehicle to the dealer for diagnostic testing. The failure mileage was approximately 103,000. VIN was unavailable.

The rear view camera is not operating when shifting to reverse. I can demonstrate this malfunction at any time to anyone. Driver is unable to detect short objects or small children directly behind the vehicle. The problem was confirmed by the dealer during a service visit. At that time, the service technician checked power and ground to the control unit and verified good. Attempted calibration for camera, vehicle would not calibrate. The vehicle has not been inspected by any other agencies. There were no warning messages, or lamps or any other symptoms prior to the failure.

Unpublished costly catastropic electrical failure Audi of America reviewed the case and declined assistance solely because the vehicle was already totaled and unavailable for dealer inspection. Audi did not dispute the presence of water intrusion, the technical findings, or the cause of failure. This failure occurred without warning under ordinary environmental conditions and resulted in sudden loss of vehicle function. I am submitting this complaint to document a potential defect related to the protection and placement of electronic systems vulnerable to water exposure. I am submitting this complaint to report a potential safety-related defect involving water intrusion and catastrophic electrical failure in a 2018 Audi S5. After a heavy rain event with no roadway flooding or submersion, my vehicle experienced complete electrical failure and would not start. Inspection revealed water intrusion into the trunk area where critical electronic components—including the battery and electronic control modules—are located. The damage was extensive and rendered the vehicle inoperable, resulting in a total loss determination. Attached documentation includes photographs, video evidence, and a technical inspection summary prepared by an independent automotive service facility and reviewed in consultation with Audi-trained technicians. The findings indicate water intrusion consistent with design vulnerability rather than misuse or lack of maintenance.