IllustrationVEHICLE RATTLING TERRIBLE, DUE TO HEAT GUARD SHIELD THAT HAD BEEN PUT OVER THE MUFFLER .
1994 Am General Hummer
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Hummer years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 0 of 2 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Equipment. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Latches/locks/linkages. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
Service Brakes, Hydraulic complaints
1 reportsOfficial recalls
396V049000 · Vehicle Speed Control:accelerator Pedal
Mar 12, 1996
THE COATING USED TO PROTECT THE ACCELERATOR PEDAL SHAFT IS INCOMPATIBLE WITH THE BRONZE BUSHING THROUGH WHICH THE SHAFT PASSES. OVER TIME, AND IN THE PRESENCE OF A CORROSIVE ENVIRONMENT (WATER, ROAD SALT), THE SHAFT CAN CORRODE INSIDE THE BUSHING INCREASING THE AMOUNT OF FRICTION BETWEEN THE ROTATING SHAFT AND THE STATIONARY BUSHING.
Consequence & remedy
Consequence: A CORRODED ACCELERATOR PEDAL SHAFT CAN CAUSE THE ENGINE THROTTLE TO BIND AND NOT FULLY RETURN TO IDLE WHEN THE OPERATOR'S FOOT IS REMOVED FROM THE ACCELERATOR PEDAL INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.
Remedy: DEALERS WILL INSTALL A REVISED ACCELERATOR PEDAL AND SHAFT ASSEMBLY.
95V023000 · Vehicle Speed Control
Feb 13, 1995
WATER CAN ACCUMULATE IN THE CRUISE CONTROL CABLE AND IF THE OUTSIDE TEMPERATURE IS BELOW FREEZING AND THE CRUISE CONTROL IS ENGAGED, THE WATER CAN FREEZE CAUSING THE CABLE TO BIND AND NOT RELEASE AS INTENDED WHEN THE BRAKE PEDAL IS APPLIED OR THE SYSTEM IS TURNED OFF AT THE MASTER CRUISE CONTROL SWITCH.
Consequence & remedy
Consequence: THE ENGINE THROTTLE CAN STICK OPEN RESULTING IN LOSS OF THROTTLE CONTROL WITH THE INCREASED POTENTIAL FOR A VEHICLE ACCIDENT.
Remedy: DEALERS WILL REMOVE THE CURRENT CRUISE CONTROL ACTUATOR AND CABLE ASSEMBLY AND INSTALL A NEW ASSEMBLY. ADDITIONALLY, DEALERS WILL CHANGE THE ROUTING OF THE CABLE.
94V164000 · Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings
Sep 1, 1994
THE OIL PRESSURE SWITCH WHICH CONTROLS THE POWER TO THE ELECTRIC FUEL PUMP CAN FAIL. FAILURE IS DUE TO A MISSING RUBBER SEAL BETWEEN THE SWITCH AND THE WIRING HARNESS. THE MISSING SEAL ALLOWS CONTAMINANTS TO ENTER THE SWITCH CAUSING IT TO FAIL IN THE OPEN OR CLOSED POSITION.
Consequence & remedy
Consequence: IF THE SWITCH FAILS IN THE CLOSED POSITION, THE PUMP WILL CONTINUE TO RUN WHEN THE ENGINE IS OFF, DRAINING THE BATTERY. IF THE SWITCH FAILS IN THE OPEN POSITION IT WILL CAUSE POOR PERFORMANCE AND POSSIBLY STALLING.
Remedy: DEALERS WILL INSPECT THE VEHICLES FOR THE PRESENCE OF THE SEAL. IF THE SEAL IS MISSING, THE SWITCH WILL BE REPLACED AND A NEW SEAL WILL BE INSTALLED.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
0No exact-year investigations in this snapshot.