Low beam headlights are very dim and nighttime driving visibility is very low. Both headlights appear to have degraded over time and fail to produce adequate light for driving. This vehicle has been brought to the dealer for repair to address this issue, and has had two related repairs that did not solve the problem. The bulb…
Read full complaint
Low beam headlights are very dim and nighttime driving visibility is very low. Both headlights appear to have degraded over time and fail to produce adequate light for driving. This vehicle has been brought to the dealer for repair to address this issue, and has had two related repairs that did not solve the problem. The bulbs have been replaced with new low-beam lamps. The headlight lens has also been restored by the dealer to reduce haze on the headlight cover. These repairs have not fixed the dim lights and the problem seems to be internal to the light. The high-beams are rarely used and do not appear to be affected by the same dim output.
NHTSA ODI #11731329
Mileage unknown · Apr 13, 2026
Exterior Lighting
Exterior lighting - HID low beams have become extremely dim and very difficult to see at night. Reading other complaints, seems like this is a very common problem with this vehicle. The manufacturer should address as this is a safety issue.
NHTSA ODI #11730859
Mileage unknown · Apr 9, 2026
Exterior Lighting
Common problem with the headlights of this model. The regular headlights become too dim, causing danger to driver at night. Using brights is mandatory during night time driving. Entire light housing must be replaced due to dimming. Replacing bulbs does not solve issue.
NHTSA ODI #11730124
Mileage unknown · Apr 4, 2026
Exterior Lighting
Low beam halogen headlights are dangerously dim. It is not possible to see in darkness without the high beams on. New factory bulbs have been replaced. Lens cleaning restoration has been performed. This widely known flaw will cause accidents if it hasn't already. Hundreds of complains have been filed with the NHTSA. There are do…
Read full complaint
Low beam halogen headlights are dangerously dim. It is not possible to see in darkness without the high beams on. New factory bulbs have been replaced. Lens cleaning restoration has been performed. This widely known flaw will cause accidents if it hasn't already. Hundreds of complains have been filed with the NHTSA. There are dozens of forums highlighting this important design flaw. The issue lies with the headlight assembly reflector becoming oxidized in a relatively short period of time. Based on research, the degradation of light emittance takes about 5-6 years to reach a dangerous visibility issue. Owners are not interested in spending $1,600 every ~6 years just to have minimum visibility while driving. This is dangerous. This is serious. This is consistent across all 2013-2015 RDX models. Sadly, my father's 1999 Ford F150 with 250K miles has original headlights which shine about 10 times brighter than this "current day" Acura. I attached a .pdf with comments from a certified Acura technician who also owns one of these vehicles. I own (2) RDX vehicles that my daughters both drive. I am considering not allowing them to drive at night in the rain because there is literally ZERO visibility. Turning the lights to the off position or on position while driving at night makes ZERO difference in visibility. The brights are fantastic and have no issue.
NHTSA ODI #11729175
Mileage unknown · Mar 26, 2026
Exterior Lighting
Headlights are extremely dim even when replaced with new bulbs. Issue has progressively worsened over years. Vehicle is unsafe to drive in the dark. Was informed I need new headlights housings from my local mechanic due to internal reflector failure.
NHTSA ODI #11727346
Mileage unknown · Mar 10, 2026
Exterior Lighting
The low beam headlights are very dim and this causes reduced / no visibility while driving at night. While driving in the dark, it is impossible to see anything on the road ahead
NHTSA ODI #11723244
Mileage unknown · Feb 11, 2026
Exterior Lighting
The low beam headlights have degraded over time and are now barely providing any light, making driving at night unsafe. This appears to be due to the degradation of the low beam assembly reflector. Replacing the low beam headlights with higher quality lights did not make any noticeable difference. This issue has been reported in…
Read full complaint
The low beam headlights have degraded over time and are now barely providing any light, making driving at night unsafe. This appears to be due to the degradation of the low beam assembly reflector. Replacing the low beam headlights with higher quality lights did not make any noticeable difference. This issue has been reported in numerous online chats for the 2015 Acura RDX.
NHTSA ODI #11717178
Mileage unknown · Feb 9, 2026
Exterior Lighting
Bought this used on February 5th 2026 Low beam headlights so dim barely illuminating driving surface
NHTSA ODI #11716676
109,573 miles · Feb 5, 2026
Exterior Lighting
The contact owns a 2015 Acura RDX. The contact stated that after purchasing the vehicle, it was discovered that the front low beam headlights failed to adequately illuminate the roadway while driving at night, causing a visibility hazard for the driver. The low beam headlights eventually became inoperable, and only the high beam…
Read full complaint
The contact owns a 2015 Acura RDX. The contact stated that after purchasing the vehicle, it was discovered that the front low beam headlights failed to adequately illuminate the roadway while driving at night, causing a visibility hazard for the driver. The low beam headlights eventually became inoperable, and only the high beam headlights were operational. Later, the high beam headlights became inoperable. The contact stated that the headlights no longer operated as needed, and the vehicle could not be driven at night. The cause of the failure was not yet determined. The local dealer was notified of the failure and informed the contact that the headlight assemblies needed to be replaced. The vehicle was not yet repaired. The manufacturer was not notified of the failure. The failure mileage was 109,573.
NHTSA ODI #11715787
Mileage unknown · Jan 23, 2026
Exterior Lighting
The headlights on the vehicle are incredibly dim. I have tried replacing the bulbs; however, it does not fix the problem. When I ask Acura about it, they say, "you're just going to have to live with it." It is incredible dangerous driving when it is dark outside because you cannot see anything unless you utilize your high beams.
Honda (American Honda Motor Co.) is recalling certain 2013 Acura ILX, 2015 RDX, 2005-2010 and 2012 RL, 2009-2014 TL, 2010 and 2012 ZDX, 2007-2011 CR-V, 2011-2013 and 2015 CR-Z, 2009-2013 Fit, 2013 Fit EV, 2010-2011 and 2013 Insight and 2007-2014 Ridgeline vehicles. These vehicles are equipped with driver frontal air bag inflators assembled as a recall remedy part or replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the driver frontal air bag inflator, free of charge. The recall began August 12, 2019. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are S5B and W59.
Honda (American Honda Motor Co.) is recalling specific 2003 Acura 3.2CL, 2013-2016 ILX, 2013-2014 ILX Hybrid, 2003-2006 MDX, 2007-2016 RDX, 2002-2003 3.2TL, 2004-2006, and 2009-2014 TL, 2010-2013 ZDX and 2001-2007 and 2009 Honda Accord, 2001-2005 Civic, 2003-2005 Civic Hybrid, 2001-2005 Civic GX NGV, 2002-2007 and 2010-2011 CR-V, 2003-2011 Element, 2007 Fit, 2002-2004 Odyssey, 2003-2008 Pilot, and 2006-2014 Ridgeline vehicles. The affected vehicles received a replacement driver air bag inflator as part of a previous Takata inflator recall remedy or a replacement driver air bag module containing the same inflator type as a service part. Due to a manufacturing error, in the event of a crash necessitating deployment of the driver frontal air bag, these inflators may explode.
Consequence & remedy
Consequence: An explosion of an inflator within the driver frontal air bag module may result in sharp metal fragments striking the driver, front seat passenger or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the driver's air bag inflator with an alternate inflator, free of charge. The recall began April 10, 2019. Honda owners may contact customer service at 1-888-234-2138. Honda's number for this recall is O41. Acura owners may contact customer service at 1-888-234-2138. Acura's number for this recall is U40.
Honda (American Honda Motor Co.) is recalling certain model year 2007-2011 Honda CR-V, 2011-2015 CR-Z, 2010-2014 FCX, and Insight, 2009-2013 Fit, 2013-2014 Fit EV, 2007-2014 Ridgeline, 2013-2016 Acura ILX, 2013-2014 Acura ILX Hybrid, 2007-2016 RDX, 2005-2012 Acura RL, 2009-2014 Acura TL, and 2010-2013 Acura ZDX vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the inflator, free of charge. The recall began March 2017. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are JY0, JY1, and JY2.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2015 Acura Rdx Problems, Complaints & Recalls | Skip That Year
Illustration